Description

Two oscillators, mutually frequency and/or phase modulated by each other.

Syntax

a1, a2 crossfm xfrq1, xfrq2, xndx1, xndx2, kcps, ifn1, ifn2 [, iphs1] [, iphs2]

a1, a2 crossfmi xfrq1, xfrq2, xndx1, xndx2, kcps, ifn1, ifn2 [, iphs1] [, iphs2]

a1, a2 crosspm xfrq1, xfrq2, xndx1, xndx2, kcps, ifn1, ifn2 [, iphs1] [, iphs2]

a1, a2 crosspmi xfrq1, xfrq2, xndx1, xndx2, kcps, ifn1, ifn2 [, iphs1] [, iphs2]

a1, a2 crossfmpm xfrq1, xfrq2, xndx1, xndx2, kcps, ifn1, ifn2 [, iphs1] [, iphs2]

a1, a2 crossfmpmi xfrq1, xfrq2, xndx1, xndx2, kcps, ifn1, ifn2 [, iphs1] [, iphs2]

Initialization

ifn1 -- function table number for oscillator #1. Requires a wrap-around guard point.

ifn2 -- function table number for oscillator #2. Requires a wrap-around guard point.

iphs1 (optional, default=0) -- initial phase of waveform in table ifn1, expressed as a fraction of a cycle (0 to 1). A negative value will cause phase initialization to be skipped.

iphs2 (optional, default=0) -- initial phase of waveform in table ifn2, expressed as a fraction of a cycle (0 to 1). A negative value will cause phase initialization to be skipped.

Performance

xfrq1 -- a factor that, when multipled by the kcps parameter, gives the frequency of oscillator #1.

xfrq2 -- a factor that, when multipled by the kcps parameter, gives the frequency of oscillator #2.

xndx1 -- the index of the modulation of oscillator #2 by oscillator #1.

xndx2 -- the index of the modulation of oscillator #1 by oscillator #2.

kcps -- a common denominator, in cycles per second, for both oscillators frequencies.

crossfm implements a crossed frequency modulation algorithm. The audio-rate output of oscillator #1 is used to modulate the frequency input of oscillator #2 while the audio-rate output of oscillator #2 is used to modulate the frequency input of oscillator #1. This double feedback structure produces a rich set of sounds with some chaotic behaviour. crossfmi behaves like crossfm except that linear interpolation is used for table lookup.

crosspm and crosspmi implement cross phase modulation between two oscillators.

crossfmpm and crossfmpmi implement cross frequency/phase modulation between two oscillators. Oscillator #1 is frequency-modulated by oscillator #2 while oscillator #2 is phase-modulated by oscillator #1.

	Warning
	Those opcodes may produce very rich spectra, especially with high modulation indexes, and in some cases foldover aliases may occur if the sampling rate is not high enough. Moreover the audio output may vary in function of the sampling rate, due to the non-linearity of the algorithm. In Csound, two other opcodes have this characteristic: planet and chuap.

Examples

Here is an example of the crossfm opcode. It uses the file Play crossfm.csd

<CsoundSynthesizer>

<CsOptions>
  -d -o dac
</CsOptions>

<CsInstruments>
sr     = 48000
ksmps  = 10
nchnls = 2
0dbfs  = 1

          instr 1
idur       =          p3 
iamp       =          p4 
ifrq1      =          p5 
ifrq2      =          p6 
indx1      =          p7 
indx2      =          p8 
kenv       linen      iamp, 0.05, idur, 0.2 
a1, a2     crossfm    ifrq1, ifrq2, indx1, indx2, 1, 1, 1 
           outs       a1*kenv, a2*kenv 
          endin

          instr 2
kx         init       0.0 
kdx        init       0.1 
kdur       init       p4 
kamp       init       p5 
kndx       init       0 
kmax       init       p6 
kfq1       init       440.0 
kfq2       init       557.0 
knx1       init       3.5 
knx2       init       4.8 
           event      "i", 1, kx, kdur, kamp, kfq1, kfq2, knx1, knx2 
kx         =          kx + kdx 
knx1       =          knx1 - 0.025 
knx2       =          knx2 - 0.075 
kndx       =          kndx + 1 
if (kndx <= kmax) kgoto nextone
           turnoff 
nextone: 
          endin
</CsInstruments>

<CsScore>
f 1 0 16384 10 1 0

i 2 0 2 0.67 0.16 150
i 1 15.1 1.5 0.1 440 557 -0.25 -6.45 0.05 1.2
e
</CsScore>
</CsoundSynthesizer>

See Also

More information on these opcodes: http://www.csoundjournal.com/issue12/crossfm.html

Credits

New in version 5.12